Jul 14, 2020 The window mechanism in a Ford Focus consists of a window motor and regulator contained in a single unit. To remove this unit, you must first remove the interior door panel. This repair is within the abilities of most vehicle owners. This procedure may take three to. 2008-2011 Ford Focus. The second-generation (Mk 2) Ford Focus was launched in 2004 as a three- and five-door hatchback and an estate variant. May 19, 2017 Hey, This is step by step procedure on door handle repair in ford focus 2008 2009 2010 2011. My problem was I could open door only from inside. This is PITA.
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to remove and reinstall a front door panel on this 2003 Ford Focus. We're going to show you the driver side, but the passenger side is pretty much the same procedure. Tools you'll need include a small and regular size flat blade screwdriver, T20 Torx driver, and a 7mm socket with a ratchet and extension.
On this door, first at the top corner, you want to pull your trim out. It should pull. This already comes off,. You pull out, and then it pulls back and off. Then you can disconnect this. Use your small screwdriver, and then you actually kind of just pry right in here on this side of the connection and pull it out. I'm just going to speed it up here with those screws, use a T20 Torx bit so use your T20 Torx bit and remove all of them. You'll want to pry this off. It's easiest to get right here in the back, pry that out, and it comes right off. Go ahead with a 7mm socket with an extension and ratchet (a ¼ mm socket actually works as well) and remove these two bolts. If you notice, I said a 1/4mm, and that's actually a quarter inch socket works just as well as the 7mm socket.
Now, this panel, actually, reach right in here and pull firmly, and here the same thing. Pull firmly and pull this panel out. Then this disconnects. There's a little tab that's back behind the wires. Push that tab down and pull that out. The tab is actually right here on the back. Push this down. Do the same thing over here. It's a couple of harnesses. They just have tabs you press with your thumb and pull out. Okay, disconnected. Now you can just take your panel, pull it out, go up, and it comes off.
To reinstall the door panel, just make sure this harness is through and this harness is up. You're going to have to have the door panel up. Get it onto the window ledge and bring it down. Reconnect our speaker. Pull this up and out, and it goes through, reconnects there. Make sure that this stays in behind. Put it on the edge first, press it forward and into place. This panel should be three connectors. Reach down the door, and bring them up through. Reconnect these two outer ones first.
Next is this lead. Make sure it's nice and free. Connect it and clip it in on the backside. Bring this back over the door handle and that goes in. I'm going to fast-forward as I take those two 7mm bolts, reinsert them into that door pull, and tighten them up. Then put the trim panel and snap it back into place.
You want to put the top in first and then snap the bottom into place. Continue that speed as I just take the seven. There's seven T20 screws: one goes in the door handle, the rest go around the perimeter of the door panel, so put those in and tighten them up. Last, but not least, put the little trim panel over the screw in the door handle.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to remove and reinstall a front door panel on this 2003 Ford Focus. We're going to show you the driver side, but the passenger side is pretty much the same procedure. Tools you'll need include a small and regular size flat blade screwdriver, T20 Torx driver, and a 7mm socket with a ratchet and extension.
On this door, first at the top corner, you want to pull your trim out. It should pull. This already comes off,. You pull out, and then it pulls back and off. Then you can disconnect this. Use your small screwdriver, and then you actually kind of just pry right in here on this side of the connection and pull it out. I'm just going to speed it up here with those screws, use a T20 Torx bit so use your T20 Torx bit and remove all of them. You'll want to pry this off. It's easiest to get right here in the back, pry that out, and it comes right off. Go ahead with a 7mm socket with an extension and ratchet (a ¼ mm socket actually works as well) and remove these two bolts. If you notice, I said a 1/4mm, and that's actually a quarter inch socket works just as well as the 7mm socket.
Now, this panel, actually, reach right in here and pull firmly, and here the same thing. Pull firmly and pull this panel out. Then this disconnects. There's a little tab that's back behind the wires. Push that tab down and pull that out. The tab is actually right here on the back. Push this down. Do the same thing over here. It's a couple of harnesses. They just have tabs you press with your thumb and pull out. Okay, disconnected. Now you can just take your panel, pull it out, go up, and it comes off.
To reinstall the door panel, just make sure this harness is through and this harness is up. You're going to have to have the door panel up. Get it onto the window ledge and bring it down. Reconnect our speaker. Pull this up and out, and it goes through, reconnects there. Make sure that this stays in behind. Put it on the edge first, press it forward and into place. This panel should be three connectors. Reach down the door, and bring them up through. Reconnect these two outer ones first.
Next is this lead. Make sure it's nice and free. Connect it and clip it in on the backside. Bring this back over the door handle and that goes in. I'm going to fast-forward as I take those two 7mm bolts, reinsert them into that door pull, and tighten them up. Then put the trim panel and snap it back into place.
You want to put the top in first and then snap the bottom into place. Continue that speed as I just take the seven. There's seven T20 screws: one goes in the door handle, the rest go around the perimeter of the door panel, so put those in and tighten them up. Last, but not least, put the little trim panel over the screw in the door handle.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Ford FocusInterior Door Panel Removal Guide
How to take off the interior door panelsof a 3rd generation MK3 2011-2014 Ford Focus to upgrade the OEM speaker.
Main Menu |
![Ford focus door lock assembly Ford focus door lock assembly](https://i.ytimg.com/vi/M8kTUYFeatE/maxresdefault.jpg)
2012 Focus Door Panel | Pry Out Round Screw Cover | Screw Cover Removed |
Thisautomotive maintenance tutorial was specifically written to assistowners of the third generation MK III (2011, 2012, 2013 & 2014) FordFocus sedan or hatchback in removing the interior door panels inorder to upgrade the OEM speaker, add soundproofing material,replace the power window motor or fix a faulty electrical switch. Owners of other similar Ford vehicles built upon the 'Global C' (C1)compact car platform such as the C-Max, Escape, Kuga and TransitConnect may also find these DIY instructions to be useful. The tools needed to complete thisprocedure include a small flathead screwdriver, a Torx T-25 star bitscrewdriver, and a standard sized flathead screwdriver or a plastic automotive trimpanel removal tool. To remove the speaker, you'll needthe Torx T-25 screwdriver, a 5.5mm socket (or a 6mm still works) anda 1/4' drive ratchet. | ||
Remove Door Handle Screw | Torx T-25 Star Bit Screw | Screw Cover - Outer Edge |
The first step isto gently pry out the circular plastic screw cover located behind the dooropener handle with the small flathead screwdriver. Remove the screw behind the door openerhandle by turning it counter clockwise with the Torx T25 star bitscrewdriver. Set the cover and screw aside in a safeplace. | ||
Pry Out Rubber Cover | Remove Torx T-25 Screw | Outer Edge Screw Removed |
Then move to theouter edge of the door panel and pry out the vinyl rubber trim panel nearthe top with the small flathead screwdriver. Remove the screw behind the cover with the TorxT25 screwdriver by turning it counter clockwise. Set the screw aside in asafe place. | ||
Pry Off Switch Panel Trim | Plastic Hook At Rear | Pry Out Switch Panel At Rear |
Then move to thefront edge of the plastic trim piece along the side of the arm rest. Gently pry off the front part of the trimpiece with the small flathead screwdriver and gently pull it off the side ofthe arm rest. Be careful when you pull off the rear edge ofthe trim panel since there is a plastic hook on that side. | ||
Arm Rest Switch Panel | Power Window Switch Plug | Press Release Button |
Next pry out therear edge of the plastic switch panel inside the arm rest. There is a plastic retaining tab at the frontof the switch panel, so do not pry out the front edge to avoid breaking it. Carefully lift the rear of the electricalswitch panel and remove it from the arm rest. Press the release button on the electricalconnector and pull the plug straight out of the socket. | ||
Switch Panel Disconnected | Arm Rest Screws Exposed | Remove Upper Torx T-25 |
Set the switchpanel aside in a safe place with the other trim pieces and screws. Once the switch panel has been removed, you'llsee the last two screws that need to be removed. Remove the two screws behind the arm rest byturning them counter clockwise with the Torx T-25 screwdriver. | ||
Remove 2nd T25 Screw | Pry Off Tweeter Panel | Sail Panel Removed |
Set the two screwsaside in a safe place. Then move to thetop inner corner of the door panel and gently pry off the sail panel whichcontains the tweeter speaker with a flathead screwdriver or trim panel tool.The sail panel is held in place by a few friction fasteners. | ||
Press Release Button | Tweeter Speaker Disconnected | Trim Panels & Screws |
Press the releasetab on the power plug and pull the tweeter speaker's electrical connectorstraight out of the socket. Set thetweeter speaker and sail panel assembly with the other parts. You should have removed a total of 4 plastictrim pieces and 4 screws. | ||
Pull Off Bottom Panel | Pull Out White Pop Rivets | Lift Panel Off Frame |
Move to the bottomedge of the door panel and firmly pull it towards yourself to disengage thewhite plastic pop rivet friction fasteners. You may need to insert a flathead screwdriveror trim panel tool to begin popping out the friction fasteners. Continuepulling out the fasteners all along the bottom and sides of the panel. Gently lift the plastic door panel up and offthe metal door frame. | ||
Light Grey Power Plug | Press Release Button - Unplug | Door Opener Handle Cable |
Angle the top ofthe door panel towards yourself while supporting the bottom with yourthighs. Press the release tab on thelight grey electrical connector and pull it straight out of the socket. | ||
Pull Back Plastic Clip | Lift Mechanism From Bracket | Door Panel Removed |
Disconnect the dooropener handle cable mechanism by gently pulling back the small black plastichandle. Lift the plastic rectangularbox piece end of the door opener cable out of the bracket. Now you can separate the door panel from theframe and set it aside in a safe place. | ||
Metal Door Frame | OEM Door Speaker | Remove Torx T-25 Screw |
To remove the doorspeaker, first take out the Torx T-25 screw on one side by turning itcounter clockwise. Then remove the hexhead screw on the other side with the 5.5mm socket and ratcheting wrench. Ifyou don't have a 5.5mm socket, you may also be able to use a slightly larger6mm socket or needle nose pliers. | ||
Remove 5.5mm Screw | Disconnect Speaker Plug | Remove OEM Speaker |
Press the releasebutton on the power connector and pull the plug straight out of the top ofthe speaker. Pull the old speaker outof the door frame. The front door speakers can be replaced with6 1/2' (6.5'), 6 3/4' (6.75') and 5 1/4' (5.25') sized aftermarket units. I'd recommend buying new aftermarket speakers fromCrutchfield since they usually include any necessary electrical connectoradapters and mounting brackets. Please verify your OEM speaker sizes andcompatible replacements before ordering anything. To help reduce road noise make your new speakerssound better, apply some Dynamat SoundDeadener to the metal door frame. It will stop rattles andvibrations when you crank up the volume. | ||
Hold Panel Near Frame | Insert Cable In To Bracket | Snap In To Place |
To replace the doorpanel, first hold it near the frame and support the bottom with your thighs. Then gently insert the plastic piece at the endof the door opener cable back in to the bracket on the door panel. Push the piece in to the bracket until itclicks securely in to place. | ||
Plug In Electrical Connector | Pull Switch Panel Plug Out | Hang Panel On Door Frame |
Push the light greypower plug back in to the socket mounted near the top of the door frame. Jmicron technologies driver for mac. Pull the electrical connector for the switchpanel out through the hole in the arm rest. Hang the top edge of the door panel on to themetal lip on the door frame. | ||
Line Up White Pop Rivets | Push Friction Fasteners In | Replace 2 Arm Rest Screws |
Line up the whiteplastic pop rivet friction fasteners on the rear of the door panel withtheir corresponding holes in the metal door frame. Firmly tap the bottom and sides of the doorpanel to push in the friction fasteners. Tighten the two screws behind the arm rest byturning them clockwise with the Torx T25 screwdriver. | ||
Push In Switch Panel Plug | First Insert Tab At Front | Gently Lower Switch Panel |
Push the electricalconnector straight in to the socket at the bottom of the switch panel. Insert the plastic tab at the front of theswitch panel in to the arm rest first and then gently push down the rearpart. | ||
Push In Switch Panel | Line Up Switch Panel Trim | First Insert Hook At Rear |
Make sure that theswitch panel is fully seated down in to the arm rest. Line up the trim piece that goes along the outeredge of the arm rest. First insert the plastic hook at the rear ofthe trim piece and then snap in the friction fasteners at the middle andfront. | ||
Gently Snap In Trim Piece | Tighten Door Handle Screw | Push In Screw Cover |
Insert the screwbehind the door opener handle and tighten it by turning it clockwise withthe Torx T25 screwdriver. Push thesmall round black plastic screw cover in place. | ||
Tighten Outer Edge Screw | Push In Rubber Screw Cover | Plug In Tweeter Speaker |
Move to the outsideedge of the door panel and insert the smaller black Torx T25 screw. Push the vinyl rubber screw cover back in toplace. | ||
Line Up Tweeter Panel | Push Sail Panel In Place | Door Panel Re-Installed |
Push the power plugback in to the socket on the tweeter speaker. Line up the friction fasteners on the rear ofthe sail panel and push it back in to place. Sit inside the vehicle, close the door, andverify that the door opener handle and electrical switches work properly. For more,check out my other Ford Focus Repair & MaintenanceGuides. |
If you found this guide to be helpful,please consider making a small donation by clicking on the PayPal.com'Donate' button located to the right of this paragraph. Thank you! (Note: I am not a registered charity. Donations are not tax deductible.) |
2011 Ford Focus Driver Door Panel Removal Tool
Main MenuHomeDigital Cameras |